Compress a stream of data into the bzip2 format.

This uses the default compression level which uses the largest compression block size for the highest compression level. Use compressWith to adjust the compression block size.

Decompress a stream of data in the bzip2 format.

There are a number of errors that can occur. In each case an exception will be thrown. The possible error conditions are:

• if the stream does not start with a valid gzip header
• if the compressed stream is corrupted
• if the compressed stream ends permaturely

Note that the decompression is performed lazily. Errors in the data stream may not be detected until the end of the stream is demanded (since it is only at the end that the final checksum can be checked). If this is important to you, you must make sure to consume the whole decompressed stream before doing any IO action that depends on it.

Like compress but with the ability to specify compression parameters. Typical usage:

compressWith defaultCompressParams { ... }

In particular you can set the compression block size:

compressWith defaultCompressParams { compressBlockSize = BlockSize 1 }

Like decompress but with the ability to specify various decompression parameters. Typical usage:

decompressWith defaultDecompressParams { ... }

The full set of parameters for compression. The defaults are defaultCompressParams.

The compressBufferSize is the size of the first output buffer containing the compressed data. If you know an approximate upper bound on the size of the compressed data then setting this parameter can save memory. The default compression output buffer size is 16k. If your extimate is wrong it does not matter too much, the default buffer size will be used for the remaining chunks.

The default set of parameters for compression. This is typically used with the compressWith function with specific paramaters overridden.

The full set of parameters for decompression. The defaults are defaultDecompressParams.

The decompressBufferSize is the size of the first output buffer, containing the uncompressed data. If you know an exact or approximate upper bound on the size of the decompressed data then setting this parameter can save memory. The default decompression output buffer size is 32k. If your extimate is wrong it does not matter too much, the default buffer size will be used for the remaining chunks.

One particular use case for setting the decompressBufferSize is if you know the exact size of the decompressed data and want to produce a strict ByteString. The compression and deccompression functions use lazy ByteStrings but if you set the decompressBufferSize correctly then you can generate a lazy ByteString with exactly one chunk, which can be converted to a strict ByteString in O(1) time using concat . toChunks.

The default set of parameters for decompression. This is typically used with the compressWith function with specific paramaters overridden.

The block size affects both the compression ratio achieved, and the amount of memory needed for compression and decompression.

BlockSize 1 through BlockSize 9 specify the block size to be 100,000 bytes through 900,000 bytes respectively. The default is to use the maximum block size.

Larger block sizes give rapidly diminishing marginal returns. Most of the compression comes from the first two or three hundred k of block size, a fact worth bearing in mind when using bzip2 on small machines. It is also important to appreciate that the decompression memory requirement is set at compression time by the choice of block size.

• In general, try and use the largest block size memory constraints allow, since that maximises the compression achieved.
• Compression and decompression speed are virtually unaffected by block size.

Another significant point applies to files which fit in a single block - that means most files you'd encounter using a large block size. The amount of real memory touched is proportional to the size of the file, since the file is smaller than a block. For example, compressing a file 20,000 bytes long with the flag BlockSize 9 will cause the compressor to allocate around 7600k of memory, but only touch 400k + 20000 * 8 = 560 kbytes of it. Similarly, the decompressor will allocate 3700k but only touch 100k + 20000 * 4 = 180 kbytes.

The WorkFactor parameter controls how the compression phase behaves when presented with worst case, highly repetitive, input data. If compression runs into difficulties caused by repetitive data, the library switches from the standard sorting algorithm to a fallback algorithm. The fallback is slower than the standard algorithm by perhaps a factor of three, but always behaves reasonably, no matter how bad the input.

Lower values of WorkFactor reduce the amount of effort the standard algorithm will expend before resorting to the fallback. You should set this parameter carefully; too low, and many inputs will be handled by the fallback algorithm and so compress rather slowly, too high, and your average-to-worst case compression times can become very large. The default value of 30 gives reasonable behaviour over a wide range of circumstances.

• Note that the compressed output generated is the same regardless of whether or not the fallback algorithm is used.

For files compressed with the default 900k block size, decompression will require about 3700k to decompress. To support decompression of any file in less than 4Mb there is the option to decompress using approximately half this amount of memory, about 2300k. Decompression speed is also halved, so you should use this option only where necessary.