XWALLPAPER(1)

NAME
xwallpaper - wallpaper setting utility for X

SYNOPSIS
xwallpaper [- -screen screen] [- -daemon] [- -debug] [- -no-randr] [- -trim widthxheight[+x+y]] [- -output output] [- -center file] [- -focus file] [- -maximize file] [- -stretch file] [- -tile file] [- -zoom file] [- -version]

DESCRIPTION
The xwallpaper program allows you to set image files as your X wallpaper. PNG file format is supported by default and preferred, but optional JPEG support exists as well.

The wallpaper is also advertised to programs which support semi-transparent backgrounds.

OPTIONS
The various options are as follows:

- -center file
    Centers the input file on the output. If the dimensions of the input file are smaller than the output dimensions, the remaining area is filled black. If the input file dimensions are too large, parts of the image will be cropped.

- -daemon
    Keeps xwallpaper running in background, listening for RandR events. In this mode, the wallpapers are redrawn when output sizes change. This option can only be used when RandR support is available and activated.

- -debug
    Displays debug messages on the standard error output while xwallpaper is running. If used in conjunction with - -daemon the process will not modify the standard input and outputs.

- -focus file
    In conjunction with - -trim the specified trim box will be guaranteed to be visible on output, zooming out if needed. If black pixels would occur around the selection, the input image is zoomed in and moved to cover them as good as possible under the constraint of keeping the specified trim box (or whole image if no trim box has been specified) on output.

- -maximize file
    Maximizes input file to fit output without cropping. This could mean zooming in or out, depending on the dimensions of the input file and the output. This option guarantees that the whole image is seen. If the ratio does not fit the output, the remaining area is filled black. The image itself will be centered on output.

- -no-randr
    Ignores individual outputs and uses the whole output instead. This is the area that spans across all different outputs (monitors).

- -trim widthxheight+x+y
    Specifies area of interest in source file. If output mode tries to output more pixels than specified with trim box, then the adjacent pixels around the box will be added to output. Black pixels are only added if no further source pixels are left.

- -output output
    Specifies the output on which a subsequently supplied file shall be set as wallpaper. You can retrieve a list of outputs on your system by executing xrandr(1). If no output is specified, all outputs will be modified individually. The special keyword all will repeat subsequent actions on all displays.

- -screen screen
    Specifies a screen by its screen number. Normally all screens of an X display are processed. Please note that a screen is not a single monitor. See - -output for such a use case above. If the output could not be found, nothing happens.

- -stretch file
    Stretches input file to fully cover the output. If the aspect ratio of the input file does not match the output, then the ratio of the input file is adjusted.

- -tile file
    Uses tiling mode. Draws the input file at the upper left corner of the output and repeats the image until the remaining area of the output is covered.

- -version
    Prints version and exits.

- -zoom file
    Zooms input file to fit output with cropping. This could mean zooming in or out, depending on the dimensions of the input file and the output. If the ratio does not fit the output, parts of the input file will not be shown. The image itself will be centered on output. Default behaviour if no option was selected.

If multiple contradicting options were given, the last supplied option wins. It is also possible to repeat output arguments without any subsequent files. In that case, the last mode and file will be reused.

EXAMPLES
Centers a PNG file as a wallpaper on LVDS-1:
    $ xwallpaper --output LVDS-1 --center file.png

Focuses on upper left corner of a JPEG file as a wallpaper on Virtual-1:
    $ xwallpaper --output Virtual-1 --trim 1x1+0+0 --focus file.jpg

Tiles a PNG file as a wallpaper across all outputs:
    $ xwallpaper --no-randr --tile file.png

Zooms into a JPEG file as a wallpaper on each output individually:
    $ xwallpaper --zoom file.jpg

Centers and recenters a JPEG file after output updates on all outputs:
    $ xwallpaper --daemon --center file.jpg

Tiles a JPEG file as a wallpaper on VGA-1 and zooms into a PNG file on LVDS-1:
    $ xwallpaper --output VGA-1 --tile file.jpg --output LVDS-1 --zoom file.png

BUGS
Use the GitHub issue tracker: https://github.com/stoeckmann/xwallpaper/issues

AUTHOR
Tobias Stockmann <tobias@stoeckmann.org>